Enterasys-networks 802.11 Instrukcja Użytkownika Strona 96
- Strona / 202
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Configuring the AP for Point-to-Multipoint
5-16
Using the RoamAbout R2 Console Port
To use the console port, follow the instructions in “Connecting a Device to the Console
Port” in Appendix B. Use Help in the console screens for a description of any field.
1. Choose Network Configuration from the Main Menu and enter the following:
IP address: Enter the IP address you wish to assign to the AP.
Subnet mask: Enter the subnet mask you wish to assign to the AP.
Default gateway: Enter the IP address of the default gateway.
Spanning Tree: For the Central AP, set to Enabled. For the APs in LAN-to-LAN
Endpoint bridge mode, you can enable or disable Spanning Tree. For more
information, see “Spanning Tree Protocol” on page 2-22.
IP Address Mode: Set to Manual when configuring an AP for the first time. For more
information, see “Modifying the IP Address” on page 5-19.
Ethernet Speed: This sets the speed of the wired Ethernet connection. The default
setting, autonegotiate, works well in most environments.
GVRP: Set to Disabled unless you are configuring the AP to support VLANs, as
described in “Configuring for VLANs” on page 5-40.
CDP: This setting is Auto Enabled by default in LAN-to-LAN mode. To change this
setting, refer to “Setting the Cabletron Discovery Protocol” on page 5-21.
2. Choose Save.
3. Choose Wireless Configuration from the Main Menu, then choose Set/Show
Wireless Configuration.
4. At the top of screen, select the radio slot (1 or 2) to configure.
5. Enter the wireless parameters.
6. Set the Reset Option to Reset Radio if necessary (default setting).
7. Choose Save.
8. If changing the bridge mode, you need to implement your changes by choosing
Reset/Upgrade in the Main Menu then choosing Reset Switch. Allow approximately
one minute for the AP to reset and complete its self-test.
Refer to the other sections in this chapter to configure features such as encryption and
filters.
- ENTERASYS.COM 1
- Contents 5
- 4 Wireless Network Tools 7
- 7 Problem Solving 10
- A PC Card Information 10
- C ASCII to HEX Conversion 11
- Glossary 11
- Intended Audience 13
- Associated Documents 14
- Document Conventions 15
- Getting Help 16
- Chapter 1 17
- RoamAbout AP 18
- RoamAbout PC Card 20
- Operating System Support 21
- Single AP 22
- Multiple APs 22
- Workgroup 23
- Wireless Client Behavior 24
- LAN-to-LAN Configuration 25
- Point-to-Multipoint 26
- Restrictions 29
- Ad-Hoc Network 31
- Optional Antennas 32
- Range Extender Antenna 33
- Outdoor Antenna Kit 34
- Chapter 2 35
- Characteristics 35
- Wireless Network Name 36
- Access Point MAC Addresses 37
- RoamAbout R2 MAC Addresses 37
- Channel Frequencies 38
- Transmit Rate 39
- Auto Rate 40
- Fixed Rate 40
- Communications Quality 41
- Data Throughput Efficiency 42
- AP Density and Roaming 42
- RTS/CTS Protocol 43
- Hidden Station 44
- 802.11 Power Management 45
- Security 46
- Transmit Key = 2 47
- Transmit Key = 1 47
- Authentication 48
- 802.1X Rapid Rekeying 50
- SNMP Community Names 53
- Console Port Security 53
- Network Protocols 54
- Wireless Traffic 54
- Message Types 55
- Spanning Tree Protocol 56
- Access Point 2000 57
- R2 Access Platform 57
- Network Configurations 58
- Static and Dynamic VLANs 59
- RoamAbout SNMP Management 60
- RoamAbout R2 61
- Chapter 3 63
- Designing and Implementing 63
- Infrastructure Network 64
- Noise from 65
- Elevator Shaft 65
- Microwave 65
- AP1 AP4AP2 67
- Using an Outdoor Antenna 68
- Chapter 4 73
- Wireless Network Tools 73
- RoamAbout AP Manager 74
- Other SNMP Management Tools 77
- RoamAbout Console Port 77
- Web Management 78
- RoamAbout Client Utility 79
- Chapter 5 81
- Required Information 83
- Viewing Current AP Settings 98
- Modifying the IP Address 99
- Using the AP Manager 101
- Modifying Wireless Parameters 102
- Using AP Manager 103
- Configuring for Security 104
- Setting Encryption 105
- RoamAbout R2 Console Port 108
- AP Manager 108
- to enter a custom AP 111
- →Programs→Control Panel 118
- Configuring for VLANs 120
- Setting Spanning Tree 123
- Protocol Description 125
- Resetting the RoamAbout AP 128
- Configuring Clients 130
- Chapter 6 131
- Using the Client Utility 135
- Logging Measurement Data 138
- Monitoring the AP Using RMON 140
- Chapter 7 147
- Problem Solving 147
- RoamAbout R2 LEDs 148
- AP 2000 LEDs 151
- AP (Classic) LEDs 154
- Showing Counters 157
- Counter Description 158
- Counter Wired Description 163
- Displaying Error Logs 164
- Transmit/Receive 165
- →Control Panel 168
- Windows NT 169
- Windows 95 or 98 170
- Appendix A 175
- PC Card Information 175
- Supported Frequency Sub-Bands 177
- Appendix B 179
- 1 5 180
- 6 9 180
- LKG-8996-931-01 180
- Appendix C 183
- ASCII to HEX Conversion 183
- ASCII Value HEX Value 184
- Glossary-2 188
- Glossary-3 189
- Glossary-4 190
- Glossary-5 191
- Index-1 193
- Index-2 194
- Index-3 195
- Index-4 196
- Index-5 197
- Index-6 198
- Index-7 199
- Index-8 200
- Index-9 201
Powiązane produkty i podręczniki dla Sprzęt komputerowy Enterasys-networks 802.11
(108 strony)LG L2000CN-SF manuels
Manuels d'utilisation et guides de l'utilisateur pour Téléviseurs et moniteurs LG L2000CN-SF.
Nous fournissons des manuels en pdf 5 LG L2000CN-SF à télécharger gratuitement par type de document : Manuel de l'utilisateur
Komentarze do niniejszej Instrukcji